"DNC-80-200-PPV-A"

Fuse Holder Double Pole Watertight Inline

Category: In-Line Fuse Holders

30 Amp, 600 Volt AC, Fuse Holder, 1-Pole, Watertight, Inline W/ Copper Set Screws

Category: In-Line Fuse Holders

Breakaway Single Pole Watertight Inline Fuseholder With Crimp Terminals

Category: In-Line Fuse Holders

1-Pole, In-Line Watertight Fuseholder for Midget and Class CC Fuses Line & Load Terminal Type: Copper Crimp

Category: In-Line Fuse Holders

Single Pole Watertight Inline Fuseholder With Crimp Terminals

Category: In-Line Fuse Holders

30Amp, 600V, Fuse Holder 1 Pole Watertight Inline Fuseholder W/ Crimp Terminals

Category: In-Line Fuse Holders

30Amp, 600V, Fuse Holder 1 Pole Watertight Inline Fuseholder W/ Crimp Terminals

Category: In-Line Fuse Holders

Eaton Bussmann series HET inline neutral fuse holder, Single-pole, Lineside: Copper crimp (1) #12-8, Loadside: Copper crimp (1) #12-8

Category: In-Line Fuse Holders

FUSEHOLDER

Category: In-Line Fuse Holders

MIDGET 1-PLOLE IN-LINE BREAKA

Category: In-Line Fuse Holders

1P In-Line Watertight Fuseholder

Category: In-Line Fuse Holders

BUS BK/HHA ATC ADD-A-CIRCUIT;

Category: In-Line Fuse Holders

(1) Insulating Boot for In-Line Fuse Holders WPB1 Contains one standard boot for use with A, B, C, D, or J termination

Category: In-Line Fuse Holders

BUSS FUSEHOLDER, 30A, Loadside: Aluminum setscrew #2-12, Lineside: Copper setscrew #3-8, 200 kA RMS Sym., Single-pole, HEB Series, Breakaway, 600V

Category: In-Line Fuse Holders

BUSS FUSEHOLDER, 30A, Loadside: Copper crimp #6; (2) #10, Lineside: Copper setscrew (2) #2-12, 200 kA RMS Sym., Single-pole, HEB Series, Breakaway, 600V

Category: In-Line Fuse Holders

1POLE INLINE FUSEHOLDER WITH CRIMP TERMI. The Littelfuse 600 V in-line watertight fuse holders are the ideal answer for all high humidity and corrosive environments where fuses are required. Available in both breakaway and non-breakaway, single and double pole versions, these fuse holders allow maximum flexibility for any application. Applications: Street, alley, and parking lot lighting. Security and perimeter lighting. Traffic signals. Outdoor illuminated signs. Sports lighting. Boat electrical circuits. Tractors and yard equipment. General outdoor circuit protection. Benefits: Safety-Permits individual fixture or device to be disconnected from circuit for servicing. Eliminates possibility of shock. Individual fixture fusing-Prevents loss of one fixture through accident, vandalism, or end of life from darkening the entire circuit. Simplifies maintenance- Being able to immediately identify the one faulted fixture eliminates testing the entire circuit, speeds repair and permits servicing the individual unit while the rest of the circuit is functioning. Reduces damage from fault-Can prevent faulted ballast or other failure from severely damaging fixture or device, reducing necessary repair or need of replacement. Features: Watertight-Internal O-ring provides watertight seal. Superior terminal seeds-Ultrasonically-welded terminals provide maximum strength and eliminate leaking at terminals. Break-Resistant- Fiberglass ûreinforced polymer body resists damage from dropping or impact much better than phenolic look-alikes. Flexible terminations-Accommodates a wide range of stranded or solid copper conductors, with either crimp or screw terminals. One-pole and two-pole models- available to accommodate all system voltages up to 600v.

Category: In-Line Fuse Holders

Fuse Holder Breakaway Double Pole Watertight Inline Feseholder

Category: In-Line Fuse Holders

Eaton Bussmann series HEX inline fuse holder, Non-breakaway, Water-resistant, 0-30 A, 600 V, Loadside: copper setscrew (1) #12-3, Lineside: copper setscrew (2) #12-3 connection, Two-pole, Used with class CC and 13/32" x 1 1/2" Fuse

Category: In-Line Fuse Holders

Breakaway Leb Type Fuseholder With Permanently Installed Neutral

Category: In-Line Fuse Holders