Raceway - Non-Metallic

Base coupler fitting. Used for joining sections of Twin-70 base together. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 90° horizontal branch from a straight horizontal run. Cover included. Black.

Category: 2-Piece Non-Metallic Raceway Tee Fittings

Panduct® type FS solid wall wiring duct, 1.5 W x 1 H, 6' length, PVC, light gray.

Category: 2-Piece Non-Metallic Raceway

One-piece latching surface raceway. Supplied with pre-applied adhesive backed tape. Available in 6', 8', and 10' lengths, International Gray, PVC, Length 8.00 ft, Width 0.77 in.

Category: 1-Piece Non-Metallic Raceway

Optional split cover for the outside vertical right angle fitting FROVRA6X4OR. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

Optional split cover for the outside vertical right angle fitting FROVRA12X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

Transition fitting from TG to T-45. Provides a tee transition from TG raceway to T-45 and LD series size 5 and 10. Use with RF5X3 reducer fitting to transition to LD series size 3.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches to 12x4 channel and/or fittings to create a horizontal four way cross intersection with two 6x4 exits. Accepts optional split cover FRFWCSC12W6YL.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Office Furniture Raceway Snap-on VerticaSnap-on single gang vertical sloped communication faceplate. Accepts up to four PANDUIT® Mini-Com® Modules (not included). No additional mounting hardware required. TIA/EIA-606-B compliant.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Communication PCommunication pole. Allows for data cable entry into office furniture raceway from suspended ceiling. 8' pole allows maximum 7' distance from top of furniture partition to ceiling. Must be used with OFR20MPT. Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

FIBERRUNNER COVER 12X4 OR 6FT

Category: 2-Piece Non-Metallic Raceway Covers

12 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Yellow.

Category: 1-Piece Non-Metallic Raceway End Fittings

Pre-Assembled Coupler for 6" x 4" Fiber Runner Channel, ASB Plastic, Yellow

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Outside corner fitting for use with LDPH5 and LDS5 raceway, Electric Ivory, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Outside corner fitting. Used to join cove raceway at outside corners. Maintains a minimum 1" bend radius of cabling.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from the 12x4 channel or a 12x4 horizontal tee, Black.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

The FiberRunner® 4-Way Cross Channel Fitting is used in cable management to create a horizontal 4-way cross intersection with two 6 inch x 4 inch exits. It also attaches to 6x4 channels and/or fittings. The 4-way cross channel fitting accepts the optional split cover.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Bend radius control trumpet for exiting at the sidewall of 2 wall heights of type G, FS, E, or S Fiber-Duct Channels.

Category: 1-Piece Non-Metallic Raceway Elbows

Raceway Spill Over FittingSpill-over fitting. Allows transition from office furniture raceway run horizontally along partition wall to office furniture vertical raceway in one location. Adjustable fitting maintains 1in minimum bend radius of cabling and works with various panel wi

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Attaches to 24x4 channel and/or fittings to create a horizontal four way cross intersection with two 24x4 exits. Accepts optional split cover FRFWCCV24YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Optional split cover for the four way cross fitting FRFWC4X4BL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19 mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

Transition fitting. Used to transition to T-70 raceway, Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Outside corner fitting for use with LDPH3 and LDS3 raceway, Electric Ivory, ABS, Length 1.05 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 12x4 channel and/or fitting to create a 45° horizontal turn from a straight horizontal run. Accepts optional split cover FRH45SC12BL.

Category: 1-Piece Non-Metallic Raceway Elbows