"wiremold"

WMD 8ATC2PCRBK 8IN PRWRD CTRL

Category: Assembled Poke-Through Units

4IN PREWIRED SURFACE DUP CR AA

Category: Assembled Poke-Through Units

Recessed Prewired Flush Style Poke-Thru Assembly, Diameter: 8 Inch, Depth: 16-1/4 Inch, Black

Category: Assembled Poke-Through Units

Includes 6" diameter poke-thru stem assembly with a disposable plate. Devices are recessed 3 1/4" (83mm) below floor surface. No cover assembly is included. For use with the following cover assemblies (purchased separately): 6CTC and 6CT Series. INCLUDED: For Side Compartments: Two (2) proprietary 20A Duplex Power Receptacles installed. For Center Compartment: One (1) 6ACT8A Mounting Plate, One (1) 6TRAC Mounting Plate, One (1) 6SER Mounting Plate. For Bottom Feed Compartment: One (1) 5BLH 1/2-Gang Pass-Through Blank Housing Assembly (Tunneling extends from the 5BLH to 575CHA so that power cables from the 20A duplex receptacle mounted on the left side of the poke-thru device are run into the junction box attached to the 575CHA.) , One (1) 1PTHA 1-Gang Pass-Through Housing Assembly, One (1) 575CHA 1/2-Gang 3/4" Conduit Housing Assembly (also includes junction box attached to the 3/4" conduit). NOTE: UL Fire Classified for up to 2-hour rated floors. Receptacles can be wired as a standard or isolated ground device.

Category: Assembled Poke-Through Units

Nonmetallic slide holder assembly. Available in black (BK), gray (GY), ivory (VY), nonmetallic brass (BS), and nonmetallic aluminum (AA). Assembled with scrub water gasket. For use on tile or carpet floors.

Category: Poke-Through Cover Assemblies

WMD 4ATP4RSB

Category: Assembled Poke-Through Units

6IN UNWIRED SURF STYLE ASSEMBLY AA

Category: Poke-Through Cover Assemblies

8IN FLUSH STYLE CVR ASSEMBLY AA

Category: Poke-Through Cover Assemblies

Bezel, (2) C6 Inserts, For EFB8S Series Mounting Bracket

Category: Assembled Poke-Through Units

Complete with hexagonal service head. Service head has one 3/4" trade size threaded conduit hub and five rubber grommets. The service head includes scrub water gasket. Unit is supplied with one 1 1/4" and one 1/2" trade size conduit stem to feed power and communication services. Service head is not to be used as a junction box. All power connections must be made in a junction box below (not supplied). Colors available in painted gray (GY), and painted black (BK). NOTE: Assembled with scrub water gasket. For use on tile or carpet floors. RC9AFFTC Series Poke-Thru Devices require a 3" (76mm) diameter hole. Not designed to work with bare concrete or terrazzo. Floor covering thickness 1/8" minimum. Gray

Category: Assembled Poke-Through Units

8" Round Cover Assembly, Evolution Series, Metallic, Cover Type: Flush, Material/Finish: Die-Cast Aluminum/Bronze Powder-Coat.

Category: Poke-Through Cover Assemblies

WMD PSRC9TCBS

Category: Assembled Poke-Through Units

WMD 10PPS 10IN PREPOUR SLEEVE

Category: Assembled Poke-Through Units

Use with AMD8C Series Covers to complete installation. AMD8 Series Poke-Thru Devices require a 4" (102mm) diameter hole. Not designed to work with bare concrete or terrazzo. Floor covering thickness 1/8" minimum.

Category: Assembled Poke-Through Units

WMD 8CREST 2G CRESTON PLATE

Category: Poke-Through Mounting Plates

WMD 6AT2PSN 6IN PREWIRED FLUS

Category: Assembled Poke-Through Units

Nonmetallic slide holder assembly. Available in black (BK), gray (GY), ivory (VY), nonmetallic brass (BS), and nonmetallic aluminum (AA). Assembled with scrub water gasket. For use on tile or carpet floors. Black

Category: Poke-Through Cover Assemblies

WMD 6ATC2PCRSN 6IN PRWRD SURF

Category: Assembled Poke-Through Units

Prewired snap-in 20A receptacle can be wired as standard duplexor isolated ground. Available only in black. See installation instructions with replacement receptacle for complete installation details.

Category: Assembled Poke-Through Units

Surface style, die-cast aluminum cover assembly with one (1) 3/4" trade size screw plug opening, and one (1) concentric 2" - 1 1/4" trade size screw plug opening. Cover assembly is available in the following powder coated finishes: (BK) black, (GY) gray, (NK) nickel, (BS) brass, and (BZ) bronze. 6CFFTC Series cover assemblies designed for use with 6STC Poke-Thru Stem Assemby. Includes one (1) 3/4" and one (1) 1/2" trade size conduit fittings and one (1) divider to separate devices. Gray

Category: Poke-Through Cover Assemblies

8IN PREWIRED SURF STYLE ASSEMBLY SB

Category: Assembled Poke-Through Units

1 1/2 GANG 1IN & 1-1/2IN CONDUIT

Category: Poke-Through Mounting Plates

Complete with one-piece finish flange and conduit assembly with one 3/4" and two 1/2" trade size conduit adapters and closure plugs. Colors available in painted gray (GY), painted black (BK), brushed aluminum (AL), and plated brass (BS). NOTE: Assembled with scrub water gasket. For use on tile or carpet floors. RC7AFFTC Series Poke-Thru Devices require a 3 1/16" (78mm) diameter hole. Not designed to work with bare concrete or terrazzo. Floor covering thickness 1/8" minimum. Anodized Aluminum

Category: Assembled Poke-Through Units

WMD 8ATC2AA

Category: Assembled Poke-Through Units