1-Piece Raceway & Accessories

OFR20 Single Channel, Low Voltage VerticOffice furniture vertical raceway. One-piece single channel raceway used to connect OFR20

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

OFR20 Single Channel, Low Voltage VerticOffice furniture vertical raceway. One-piece single channel raceway used to connect OFR20

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

One-piece latching surface raceway. Supplied with pre-applied adhesive backed tape.Available in 6', 8', and 10' lengths.

Category: 1-Piece Non-Metallic Raceway

Base coupler fitting. Used for joining sections of Twin-70 base together. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Two channel tamper resistant one-piece latching surface raceway. Supplied with pre-applied adhesive backed tape. Available in 8' and 10' lengths.

Category: 1-Piece Non-Metallic Raceway

Office Furniture Raceway Snap-on VerticaSnap-on single gang vertical sloped communication faceplate. Accepts up to four PANDUIT® Mini-Com® Modules (not included). No additional mounting hardware required. TIA/EIA-606-B compliant.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Tee fitting. Used to join sections of cove raceway to form a "tee" junction. Maintains a minimum 1" bend radius of cabling.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Office Furniture Raceway Communication PCommunication pole. Allows for data cable entry into office furniture raceway from suspended ceiling. 8' pole allows maximum 7' distance from top of furniture partition to ceiling. Must be used with OFR20MPT. Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Transition fitting from TG to T-45. Provides a tee transition from TG raceway to T-45 and LD series size 5 and 10. Use with RF5X3 reducer fitting to transition to LD series size 3.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

End cap fitting. Conduit breakouts of 1/2" for entry into raceway channel. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway End Fittings

Tee fitting with divided insert to maintain separation of power and data cabling. For use with LD2P10 raceway, White.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

One-piece latching surface raceway. Supplied with pre-applied adhesive backed tape. Available in 6', 8', and 10' lengths, International Gray, PVC, Length 8.00 ft, Width 0.77 in.

Category: 1-Piece Non-Metallic Raceway

Power rated drop ceiling/entrance end fitting for use with LD3, LDPH3, LDS3, LD5, LDPH5, LDS5, LD10 and LDPH10 raceway. Use CA3 or CA5 adapters for LD3/LDPH3/LDS3 and LD5/LDPH5/LDS5 profile raceway, adapters not required for LD10 and LDPH10 raceway, Inter

Category: 1-Piece Non-Metallic Raceway End Fittings

Outside corner fitting for use with LDPH5 and LDS5 raceway, Electric Ivory, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway Elbows

End cap fitting. Conduit breakouts of 1/2" for entry into raceway channel. White.

Category: 1-Piece Non-Metallic Raceway End Fittings

Outside corner fitting for use with LDPH3 and LDS3 raceway, Electric Ivory, ABS, Length 1.05 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Reducer fitting for use with LD5, LDPH5, LDS5, LD10 and LDPH10 raceway. For in-line terminations, use with CFX10, Off White, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Reducer fitting for LD raceway from size 5 to size 3. For use with LD5 and LD3 raceway. For in-line terminations, use with CF5, Electric Ivory, ABS, Length 0.85 in.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Entrance end fitting. Conduit breakouts of 1/2", 3/4", 1", and 1 1/4" which allows entry from ceiling or wall. International Gray.

Category: 1-Piece Non-Metallic Raceway End Fittings

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2LG or FIVRA4X4LG to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Raceway Spill Over FittingSpill-over fitting. Allows transition from office furniture raceway run horizontally along partition wall to office furniture vertical raceway in one location. Adjustable fitting maintains 1in minimum bend radius of cabling and works with various panel wi

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Base coupler fitting. Used for joining sections of Twin-70 base together. White.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Adapter fits into universal breakout of DCEFX or RAEFX fittings. For use LD5, LDPH5, and LDS5 raceway, Electric Ivory, PVC, Length 0.81 in.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Bend radius control trumpet for exiting at the sidewall of 2 wall heights of type G, FS, E, or S Fiber-Duct Channels.

Category: 1-Piece Non-Metallic Raceway Elbows