1-Piece Raceway & Accessories

Office Furniture Raceway End CapEnd cap fitting. Used to terminate office furniture raceway. Supplied with adhesive tape. Office Beige.

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches to 6x4 channel and/or fittings to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FROVRA6X4OR to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from the 12x4 channel or a 12x4 horizontal tee, Yellow.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches to 12x4 channel and/or fitting to create a 45° upward angle from a straight horizontal run. Used with outside vertical 45° angle fitting FROV4512X4YL to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 8' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

End cap fitting. Used to terminate or allow entry to T-70 raceway with conduit breakouts of 1/2" . International Gray.

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches to 12x4 channel and/or fittings to create a 90° vertical turn down from a straight horizontal run. Accepts optional split cover FROVRASC12YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 12x4 channel and/or fittings to create a 90° horizontal branch with a 4x4 exit from straight horizontal run. Accepts optional split cover FRTSC12W4YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 6x4 channel and/or fittings to create a 45° downward angle from a horizontal run. Used with inside vertical 45° angle fitting FRIV456X4YL to change level of a straight horizontal run. Accepts optional split cover FROV45SC6OR.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FROVRA4X4YL to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 24x4 channel and/or fittings to create a 90° horizontal branch with a 12x4 exit from straight horizontal run. Accepts optional split cover FRTCV24W12YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Entrance end fitting for LD2P10 raceway. Breakouts for 1/2" and 3/4" diameter conduit. Off White.

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches to 4x4 channel and/or fitting to create a 90° horizontal turn from a straight horizontal run. Accepts optional split cover FRRASC4OR.

Category: 1-Piece Non-Metallic Raceway Elbows

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2BL or FIVRA4X4BL to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Optional split cover for the horizontal right angle fitting FRRA4X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fittings to create a 90° vertical turn down from a straight horizontal run. Accepts optional split cover FROVRASC4YL.

Category: 1-Piece Non-Metallic Raceway Elbows

The fiber routing vertical tee attaches to a 6x4 channel and/or fittings to create a 90° vertical drop from a straight horizontal run. A hinged door is included. It accepts FTR4X4YL, FIDT4X4BL, S4X4YL6, or E4X4YL6 directly. It also accepts optional snap-o

Category: 1-Piece Non-Metallic Raceway Elbows

One-piece latching surface raceway. Supplied with pre-applied adhesive backed tape.Available in 6', 8', and 10' lengths.

Category: 1-Piece Non-Metallic Raceway

Attaches to 12x4 channel and/or fitting to create a 90° horizontal turn from a straight horizontal run. Inside divider walls manage cables routed around horizontal right angles. Accepts optional split cover FRRASC12BL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 6x4 channel and/or fittings to create a horizontal four way cross intersection. Accepts optional split cover FRFWCSC6BL.

Category: 1-Piece Non-Metallic Raceway Elbows

The FiberRunner® QuikLock™ Coupler is a pre-assembled coupler designed to quickly join two sections of channel and/or fittings in a cable routing system. The coupler measures 12 inches x 4 inches. No tools are required for installation.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from 6x4 channel, 6x4 horizontal tee fitting, or 6x4 exit on 12x4 vertical tee, Yellow.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Office Furniture Raceway Desk Mount BoxDesk mount box. Box accepts office furniture snap-on faceplates as well as 70mm NEMA standard screw-on faceplates. Designed for use with OFVR56 raceway and OFR20SO, OFR20DSO spill-over fittings. Supplied with adhesive tape.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Snap-on HorizonSnap-on single gang horizontal sloped communication faceplate. Accepts up to four PANDUIT® Mini-Com® Modules (not included). No additional mounting hardware required. TIA/EIA-606-B compliant.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings