Search results

Raceway two-piece base and cover, TG-70, Off White, 8'

Category: 2-Piece Non-Metallic Raceway

The black powder coated bracket strut mounting clip assembly in black is 2.27 (57.7 mm) high, 6.50 (165.1 mm) long, and 1.96 (49.8 mm) wide. It allows the Wyr-Grid ® Pathway to be attached directly to standard 1.63 (41.4) wide strut structures. The packag

Category: Wire Duct Clips / Retainers

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 8' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway End CapEnd cap fitting. Used to terminate office furniture raceway. Supplied with adhesive tape. Office Beige.

Category: 1-Piece Non-Metallic Raceway End Fittings

Reducing Fitting, 4x4 Fiber Duct, Cover Included, ABS, Yellow

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Tee fitting. Used to join sections of Twin-70 raceway at tee intersections, Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Tee Fittings

The FiberRunner® QuikLock™ Coupler is a pre-assembled coupler designed to quickly join two sections of channel and/or fittings in a cable routing system. The coupler measures 12 inches x 4 inches. No tools are required for installation.

Category: Couplers & Joiners

End cap fitting. Used to terminate or allow entry to T-70 raceway with conduit breakouts of 1/2" . International Gray.

Category: 1-Piece Non-Metallic Raceway End Fittings

Twin-70 raceway base, 10 foot length. Supplied with pre-punched mounting holes. 2' of cover needed for every 1' of Twin-70 base.

Category: 2-Piece Non-Metallic Raceway

PAN PED6 PATCHRUNNER HIGH CAPACITY 6.1 (155MM) D

Category: Special Purpose Wire Duct

Outside corner fitting. Used to join sections of Twin-70 raceway at outside corners. Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Panduct® PanelMaxâ„¢ replacement cover for DIN rail wiring duct, 3" replacement cover, PVC, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Wire Duct Covers

Single gang two-piece screw together outlet box. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use withPan-Way® LD profile raceway. 5.19"L x 3.45"W x 1.75"H (131.9mm x 87.7mm x 44.4mm). Breakouts for 1/2", 3/4", or 1" diameter conduit.

Category: 1-Gang Raceway Device Boxes

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2BL or FIVRA4X4BL to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Optional split cover for the horizontal 45° angle fitting FRH454X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: Elbows & Bends

Pre-assembled 12in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Orange, 1 piece.

Category: Couplers & Joiners

Attaches to 4x4 channel and/or fitting to create a 90° horizontal turn from a straight horizontal run. Accepts optional split cover FRRASC4OR.

Category: Elbows & Bends

Attaches to 4x4 channel and/or fittings to create a 90° vertical turn down from a straight horizontal run. Accepts optional split cover FROVRASC4YL.

Category: Elbows & Bends

Duct cover, 4 W x 6' length, PVC, orange, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Wire Duct Covers

The fiber routing spill-over junction is used to fully enclose a 6x4 channel in conjunction with the spill-over junction FRSPJ2X2YL. The cover snaps onto the channel base. A hinged feature allows easy access to add or remove cables. It is yellow and made

Category: Drop-Offs, Spillouts & Outlets

The L-bracket with quick mount clip is used for installing the CWD4 corner wiring duct. It is made of low-carbon steel and spring steel and comes in a package of 16 pieces. The recommended fastener size is #10 – 32 x 1/2" (not

Category: Small 2-Piece Metallic Raceway Clips, Connectors, & Couplings

Attaches to 6x4 channel and/or fittings to create a horizontal four way cross intersection. Accepts optional split cover FRFWCSC6BL.

Category: Tees, Crosses & Junctions

Optional split cover for the horizontal right angle fitting FRRA4X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: Elbows & Bends

SLD DUCT NMTG PVC 3IN X5IN X6FT WHT 6FT

Category: 2-Piece Non-Metallic Raceway