Search results

For AC8840 and AC8104 Boxes. Includes two (2) Ortronics Series II adapters and two (2) TracJack adapters. NOTE: AC8840 is a single-service box. Power plates cannot be used in conjunction with communication plates.

Category: Communication Module End Plates For Metallic Raceway

20a Replacement Device. 6" (152mm) Wire Leads Each Side.

Category: Plugmold Device Boxes

Two-compartment large capacity pole. Furnished unwired without outlets. Box ended with industry sized knockouts. Standard heights: 10' 2" (3.1m) (NP800C-10-2B), 12' 8" 3.9m) (NP800C-12-8B), 15' 2" (4.6m) (NP800C-15-2B) Finish - Anodized Aluminum

Category: Aluminum Power Poles

WMD TBCRHMK HORIZONTAL MOUNTI

Category: Recessed Home Entertainment Box Covers

Flanged cover for use in tile or carpet installation. Die-cast aluminum assembly. Insert in lid allows for carpet or tile cutouts to match finished floor. NOTE: Add suffix “TR" to the end of the part number to indicate tamper-resistant cover assembly. Tamper-resistant versions are secured with a single tamper-resistant screw. "NA" indicates North American made and complies with the Buy American Act, NAFTA, and ARRA requirements.

Category: Square / Rectangle Recessed Box Covers

Combination Carpet and Tile Flange, 3-Gang, Powder-Coated Aluminum, Bronze

Category: Square / Rectangle Recessed Box Flanges

Attaching ring for Source I (preset or afterset) zinc die-cast. 4" (102mm) O.D. 3 1/8" ring depth. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

Nonmetallic slide holder assembly. Available in black (BK), gray (GY), ivory (VY), nonmetallic brass (BS), and nonmetallic aluminum (AA). Assembled with scrub water gasket. For use on tile or carpet floors.

Category: Poke-Through Cover Assemblies

Includes 6" diameter poke-thru stem assembly with a disposable plate. Devices are recessed 3 1/4" (83mm) below floor surface. No cover assembly is included. For use with the following cover assemblies (purchased separately): 6CTC and 6CT Series. INCLUDED: For Side Compartments: Two (2) proprietary 20A Duplex Power Receptacles installed. For Center Compartment: One (1) 6ACT8A Mounting Plate, One (1) 6TRAC Mounting Plate, One (1) 6SER Mounting Plate. For Bottom Feed Compartment: One (1) 5BLH 1/2-Gang Pass-Through Blank Housing Assembly (Tunneling extends from the 5BLH to 575CHA so that power cables from the 20A duplex receptacle mounted on the left side of the poke-thru device are run into the junction box attached to the 575CHA.) , One (1) 1PTHA 1-Gang Pass-Through Housing Assembly, One (1) 575CHA 1/2-Gang 3/4" Conduit Housing Assembly (also includes junction box attached to the 3/4" conduit). NOTE: UL Fire Classified for up to 2-hour rated floors. Receptacles can be wired as a standard or isolated ground device.

Category: Assembled Poke-Through Units

Surface Style Floor Box Cover Assembly with Insert, Material/Finish: Die Cast Aluminum/Bronze

Category: Square / Rectangle Recessed Box Covers

6' Plugmold Multioutlet USB system Gray

Category: Single Circuit Tamper Proof Plugmold

Blank Flanged Cover Assembly. Die-Cast Aluminum. Color: Black. For use with: Tile, Carpet. Origin: USA

Category: Square / Rectangle Recessed Box Covers

Combination Carpet and Tile Flange, 3-Gang, Powder-Coated Aluminum, Gray

Category: Square / Rectangle Recessed Box Flanges

Kit comes complete with adapter ring to secure into the boxes, Wiremold CM Series open system adapters (unloaded), Ortronics Series II, and TracJack adapters. Modular jacks and A/V connectors sold separately.

Category: Round Recessed Box Covers

1 1/4" IPS locking nipple for 525 and Multiplex Series fittings. 1 1/2" long. Finish - Anodized Aluminum

Category: Recessed Floor Box Service Fittings

<p>Dual-service fitting includes housing, base, two mounting frames, divider, and mounting hardware. For use on one No. 2 and one No. 4 Duct. Has 1/2'' and 3/4'' trade size conduit knockouts on each end. 104.3 cu. in. (1709cm3) capacity.</p>

Category: Recessed Floor Box Service Fittings

For mounting up to three power or communication devices at one location inline and offset with 5400 Series Raceway. For use with 5507 Series Faceplates, Ortronics TracJack and Series II Modules, Pass and Seymour Activate Series Inserts, Wiremold Open System Communication Modules. NOTE: CM-EPLA End Plates are required when using Wiremold communication modules. S2-EPL End Plates are required when using Orthonics Series II Inserts. To mount TracJack inserts, use 5507-4TJ or 5507-6TJ Faceplates. White

Category: 3-Gang Raceway Device Brackets & Plates

6' Plugmold Multioutlet System with 8 single outlets 9 inches apart, GB Finish - Gray

Category: Single Circuit Steel Plugmold

Receptacle opening 1 9/16" (40mm). For 6" poke-thru units only.

Category: Square / Rectangle Recessed Box Covers

For deep switches and receptacles. Base has two 1/2" trade size KOs. Larger gang boxes available by special order. Five-gang: 4 5/8" L x 10 5/32" W (117mm x 258mm). NOTE: Certified to Canadian Safety Standards for sale in Canada. When ordering these products, change the "V" color prefix to "VC" to denote the Canadian versions.

Category: 5-Gang Raceway Device Boxes

Receptacle opening 1 9/16" (40mm). For 8" poke-thru units only.

Category: Recessed Floor Box Service Fittings

For making a 90 degree external turn in a raceway run. Includes four ALA01 Couplings.

Category: Large 2-Piece Metallic Raceway Elbows

Nonmetallic Plugmold 6' in length with receptacles spaced 18" on center. Nonmetallic Plugmold has a textured ivory finish. For use with 20 amp circuit. Finish - Ivory

Category: Single Circuit Non-Metallic Plugmold

DUCT COUPLING ASSEMBLY

Category: Large 2-Piece Metallic Raceway Clips, Connectors, & Couplings