1-Piece Raceway & Accessories

Attaches to a 12x4 channel and/or fittings to create a horizontal four way cross intersection with two 4x4 exits, Black.

Category: 1-Piece Non-Metallic Raceway Elbows

OFR20 Single Channel, Low Voltage VerticOffice furniture vertical raceway. One-piece single channel raceway used to connect OFR20

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

OFR20 Single Channel, Low Voltage VerticOffice furniture vertical raceway. One-piece single channel raceway used to connect OFR20

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Attaches to 24x4 channel and/or fittings to create a 45° upward angle from a straight horizontal run. Used with outside vertical 45° angle fitting FROV4524X4YL to change level of a straight horizontal run. Includes cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 24x4 channel and/or fittings to create a 45° horizontal turn from a straight horizontal run, Yellow.

Category: 1-Piece Non-Metallic Raceway Elbows

End cap fitting. Conduit breakouts of 1/2" for entry into raceway channel. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches to 6x4 channel and/or fittings to create a 90° horizontal branch from straight horizontal runs. Accepts optional split cover FRTSC6BL.

Category: 1-Piece Non-Metallic Raceway Elbows

Tee fitting with divided insert to maintain separation of power and data cabling. For use with LD2P10 raceway, White.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches any 6x4 FiberRunner® Fitting or Channel to any 4x4 FiberRunner® Fitting or Channel. Accepts split cover FRRF6FR4SCYL.

Category: 1-Piece Non-Metallic Raceway Elbows

Tee fitting. Used to join sections of cove raceway to form a "tee" junction. Maintains a minimum 1" bend radius of cabling.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Power rated drop ceiling/entrance end fitting for use with LD3, LDPH3, LDS3, LD5, LDPH5, LDS5, LD10 and LDPH10 raceway. Use CA3 or CA5 adapters for LD3/LDPH3/LDS3 and LD5/LDPH5/LDS5 profile raceway, adapters not required for LD10 and LDPH10 raceway, Inter

Category: 1-Piece Non-Metallic Raceway End Fittings

24 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Black.

Category: 1-Piece Non-Metallic Raceway End Fittings

The fitting attaches any 12x4 FiberRunner® Fitting or Channel to any 6x4 FiberRunner® Fitting or Channel while transitioning to the left. It is black and made of ABS plastic. It accepts split cover FRRF126LSCBL.

Category: 1-Piece Non-Metallic Raceway Elbows

Two channel tamper resistant one-piece latching surface raceway. Supplied with pre-applied adhesive backed tape. Available in 8' and 10' lengths.

Category: 1-Piece Non-Metallic Raceway

Base coupler fitting. Used for joining sections of Twin-70 base together. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

One-piece latching surface raceway. Supplied with pre-applied adhesive backed tape. Available in 6', 8', and 10' lengths, International Gray, PVC, Length 8.00 ft, Width 0.77 in.

Category: 1-Piece Non-Metallic Raceway

Transition fitting from TG to T-45. Provides a tee transition from TG raceway to T-45 and LD series size 5 and 10. Use with RF5X3 reducer fitting to transition to LD series size 3.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Office Furniture Raceway Snap-on VerticaSnap-on single gang vertical sloped communication faceplate. Accepts up to four PANDUIT® Mini-Com® Modules (not included). No additional mounting hardware required. TIA/EIA-606-B compliant.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Communication PCommunication pole. Allows for data cable entry into office furniture raceway from suspended ceiling. 8' pole allows maximum 7' distance from top of furniture partition to ceiling. Must be used with OFR20MPT. Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

12 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Yellow.

Category: 1-Piece Non-Metallic Raceway End Fittings

Outside corner fitting for use with LDPH5 and LDS5 raceway, Electric Ivory, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Outside corner fitting. Used to join cove raceway at outside corners. Maintains a minimum 1" bend radius of cabling.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from the 12x4 channel or a 12x4 horizontal tee, Black.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

The FiberRunner® 4-Way Cross Channel Fitting is used in cable management to create a horizontal 4-way cross intersection with two 6 inch x 4 inch exits. It also attaches to 6x4 channels and/or fittings. The 4-way cross channel fitting accepts the optional split cover.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters