"terminal blocks"

Copper Terminal Lug 1/0 - 4 AWG Copper Terminal Lugs are made of high copper alloy. They are used for joining a wide range of cables or terminal blocks.

Category: 1-Conductor Copper Mechanical Lugs

Feed Through Terminal Block. Screw Clamp. Type: M 2,5/5. Color: Gray. 600V/30A. Size: 2.5 mm Block, 5 mm Spacing. DIN 1 - DIN 3. Wire Size: 22 - 12 AWG.

Category: 2.5mm Feed Through & Ground Terminal Blocks

510A PWR DIST BLOCK

Category: Double Primary / Multiple Secondary Non-Insulated Distribution Blocks

Distribution Block, 2-Pole, 175 Amps, 600V, Line Side: (1) 2/0 - 14 AWG, Load Side: (4) 4 - 14 AWG

Category: Single Primary / Multiple Secondary Non-Insulated Distribution Blocks

Homac CSB-2/0-3 2-Way 3-Outlet Encapsulated Multi-Tap Cable Block, Alum/Copper/Stranded Conductor, Alum

Category: Dual Sided Entry Wire Connector Blocks

Fuse Bases, 200 Amp, Stud Height: 1.75 Inch, Stud Thread: 5/16-18, Base Material: Phenolic, The Simpler Design Is The C5268 Series Modular Fuse Base. With This Design, The Fuse Terminal and Cable (With Termination) Are Mounted on The Same Stud, Minimizing Labor Needed For Installation.

Category: Terminal Junction Blocks

MAR 1333598 510A PWR DIST BLOCK

Category: Multiple Primary / Multiple Secondary Non-Insulated Distribution Blocks

AB 700-HLT1A2 TERM BLK RELAY 240V

Category: Interface Relay Terminal Blocks

Insulated Multi-Cable Connector Block For Fine Stranded Flexible Copper Conductors And For 1-Wires And In-Line Splicers/Reducers, 600V, Number of Ports: 2, Wire Range: 14 AWG - 6 AWG, Abrasion And Chemical Resistant, Rated For Use With Copper Conductors

Category: Single Sided Entry Wire Connector Blocks

Ground Terminal Block with Rail Contact. Screw Clamp. Type: SNK, ZS4. Color: Green/Yellow. 5.2 mm Spacing. DIN 1 - DIN 3. Snap-in rail connection.

Category: Ground Terminal Blocks

Ideal; Terminal Strip; Wire Size: 22 - 6 Awg; Spacing: 0.625 In; Amperage Rating: 60 Amp; Voltage Rating: 600 V; Material: Nickle-plated Brass; Number Of Circuits: 12; Torque Rating: 20 In-lb; Terminal Screw Size: 12

Category: Terminal Strips

Power Splicer Block, 175A, 600V AC/DC, 2-Pole, (1) In/Out, (1) 14 - 2/0 AWG Line Side, (1) 14 - 2/0 AWG Load Side

Category: Single Primary / Single Secondary Non-Insulated Distribution Blocks

BUS KUX4 TERM BLOCK BLACK NOR

Category: Terminal Strips

Copper Terminal Lug 250 MCM - 1/0 AWG Copper Terminal Lugs are made of high copper alloy. They are used for joining a wide range of cables or terminal blocks.

Category: 1-Conductor Copper Mechanical Lugs

Power Distribution Block, 3 Pole, 175 Amp, 600 Volt AC/DC, 1 In, 4 Out

Category: Single Primary / Multiple Secondary Non-Insulated Distribution Blocks

M-thn Ch1322 Clr Plst Pwr Blo

Category: Non-Insulated Connector Block Covers

Terminal Block, 3 Circuit, Feed Through, 10 Amp, 300 Volt AC/DC, Gray, 2.5 mm, for PNP Device, 50 in a Package

Category: Three Level Sensor Terminal Blocks

Homac CSB-250-2-S 1-Way 2-Outlet Encapsulated Multi-Tap Cable Block, Alum/Copper/Stranded Conductor, Alum

Category: Single Sided Entry Wire Connector Blocks

Center Jumper, Plug-In Type, 10 mm Center to Center, 2 Pole, Yellow, Pkg. Qty. of 25, for Use With 1492-L10

Category: Terminal Block Jumper Bars

Power Distribution Block, Double Primary-Multiple Secondary, 4 AWG to 500 MCM, 760 Amp, 600 Volt, Aluminum, Phenolic

Category: Double Primary / Multiple Secondary Non-Insulated Distribution Blocks

MAR 1333588 420A PWR DIST BLOCK

Category: Single Primary / Multiple Secondary Non-Insulated Distribution Blocks

AB 1492-CA2175 TERMINAL BLOCK 600V

Category: 10mm Feed Through & Ground Terminal Blocks

MAR 1433123 3CKT POWER BLOCK

Category: Single Primary / Single Secondary Non-Insulated Distribution Blocks

Snap-On Separator End Section for Rails / Separators. Type: SCFM6. Color: Gray. Thickness: 3 mm. Used with Terminal Block Type: M 4/6, M 6/8 and M 10/10. ***Allows mounting of a protective cover CPM, and a marker-holder PEP. Mounting on PR1, PR3, PR4 and PR5 Rails***

Category: Terminal Block End Sections