Search results

Snap-on single gang 106 duplex electrical/communication faceplate. Used to cover one NEMA standard 106 duplex electrical outlet. In communication applications, covers one standard 106 duplex communication module frame.

Category: Metallic Overfloor Raceway Device Plates

Tee fitting for use with LDPH3 and LDS3 raceway, White, ABS, Length 2.23 in.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

End Cap Fitting For Use With LDPH5 And LDS5 Raceway, Non-Metallic, Off-White

Category: 1-Piece Non-Metallic Raceway End Fittings

Panduct® type G wide slot wiring duct, 1.5 W x 1 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type G wide slot wiring duct, 4 W x 1.5 H, 6' length, PVC, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Inside corner fitting for use with LD10 and LDP10 raceway, Electric Ivory, ABS, Length 2.49 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Panduct® solid divider wall, 3.00" nominal duct height, 6' length, PVC, white.

Category: Wall Duct Dividers

Panduct® type F narrow slot wiring duct, 1 W x 3 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

FS Solid Wall Wiring Duct, 2 W x 2 H, 6' Length, PVC, White, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Special Purpose Wire Duct

Panduct® type F narrow slot wiring duct, 1 W x 4 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Outside Corner Fitting For Use With LDPH5 And LDS5 Raceway, White, ABS, Length 2.86 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Drop ceiling/entrance end fitting for use with LD5 raceway, International Gray, ABS, Length 3.42 in.

Category: 1-Piece Non-Metallic Raceway End Fittings

Panduct® type F narrow slot wiring duct, 1.5 W x 1.5 H, 6' length, PVC, intrinsic blue, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

End Cap Fitting, LDPH3/LDS3 Raceway, Non-Metallic, White

Category: 1-Piece Non-Metallic Raceway End Fittings

Optional snap-on hinged cover for channel FR6X4BL6. Hinge feature enables positioning of cover at angles between 30° and 90°.

Category: 2-Piece Non-Metallic Raceway Covers

Panduct® type F narrow slot wiring duct, .5 W x .5 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Panduct® type FS solid wall wiring duct, 1.5 W x 2 H, 6' length, PVC, light gray.

Category: 2-Piece Non-Metallic Raceway

Panduct® type F narrow slot wiring duct, 1 W x 1 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8', and 10' lengths, Electric Ivory, Length 10.00 ft.

Category: 2-Piece Non-Metallic Raceway

The fiber mounting FiberRunner® QuikLock™ Threaded Rod Trapeze Bracket for Wyr-Grid® 12" (305mm) width is used to support a FiberRunner® 4x4 and 6x4 Channel above or below the Wyr-Grid® 12" Pathway using the same 1/2" or 12mm threaded rod used to support

Category: Cable Tray Trapeze Hangers

Right Angle Fitting, Used To Join Sections Of T-70 Raceway At Right Angles, Electric Ivory

Category: 1-Piece Non-Metallic Raceway Elbows

T-70, TG-70, or Twin-70 raceway cover, 10 foot length.

Category: 2-Piece Non-Metallic Raceway Covers

End cap fitting for use with LDPH5 and LDS5 raceway, Electric Ivory, ABS, Length 1.00 in.

Category: 1-Piece Non-Metallic Raceway End Fittings

Panduct® flush cover type D round hole wiring duct, 2 W x 2 H, 6' length, PVC, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct