Search results

Used to carry cables horizontally throughout the system. Use QuikLock Coupler FRBC24X4YL to attach channel and/or fittings.

Category: Straight Sections

End cap fitting for use with LDPH10 and LD2P10 raceway, International Gray, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway End Fittings

Used to support the 12x4 system from existing threaded rod installations. Bracket is secured to threaded rod with two split nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps, For 5/8" Threaded Rod.

Category: Mounting Hardware & Brackets

Raceway, Non-Metallic, Low Voltage, One-Piece, Hinged, 6 Foot, Gray

Category: 1-Piece Metallic Raceway

Panduct® flush cover type D round hole wiring duct, 1 W x 3 H, 6' length, PVC, black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Special Purpose Wire Duct

Panduct® type FS solid wall wiring duct, 2 W x 3 H, 6' length, PVC, white, no mounting holes.

Category: 2-Piece Non-Metallic Raceway

Panduct® type FS solid wall wiring duct, 1.5 W x 1 H, 6' length, PVC, white, no mounting holes, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8', and 10' lengths, Electric Ivory, PVC, Length 10.00 ft, Width 1.02 in.

Category: 2-Piece Non-Metallic Raceway

Panduct® type FS solid wall wiring duct, 3 W x 2 H, 6' length, PVC, white.

Category: 2-Piece Non-Metallic Raceway

Panduct® type G wide slot wiring duct, 3 W x 3 H, 6' length, PVC, adhesive, black.

Category: Standard Density Wire Duct

T-45 entrance end fitting. With knockouts for 1/2", 3/4", 1" and 1 1/4" conduit which allows entry from ceiling or wall, White.

Category: 2-Piece Non-Metallic Raceway End Fittings

Panduct® type G wide slot wiring duct, .75 W x 1.5 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Raceway Tee Fitting, LD5 Series Raceway, Non-Metallic, Electric Ivory

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Net-Contain™ Universal Aisle Containment Vertical Wall Brace - 4ft. (1200mm) aisle width, white.

Category: Wall Duct Dividers

Panduct® type F narrow slot wiring duct, 3 W x 2 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Panduct® type F narrow slot wiring duct, .75 W x 1.5 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Raceway Base and Cover, Above Floor, Office Slate, 6 Foot, 4-Channel

Category: 2-Piece Non-Metallic Raceway

Inside corner fitting. Used to join sections of T-70 raceway at inside corners

Category: 2-Piece Non-Metallic Raceway Elbows

Right angle fitting for use with LD5 raceway, Electric Ivory, ABS, Length 2.00 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Panduct® type G wide slot wiring duct, .75 W x 2 H, 6' length, PVC, blac, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Tee fitting. Used to join sections of T-70 raceway at tee intersections, Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Panduct® type F narrow slot wiring duct, 1 W x 4 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Panduct® flush cover type D round hole wiring duct, 3 W x 4 H, 6' length, PVC, black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Power rated drop ceiling/entrance end fitting for use with LD3, LDPH3, LDS3, LD5, LDPH5, LDS5, LD10 and LDPH10 raceway. Use CA3 or CA5 adapters for LD3/LDPH3/LDS3 and LD5/LDPH5/LDS5 profile raceway, adapters not required for LD10 and LDPH10 raceway, Electric Ivory, PVC, Length 4.1 in.

Category: 1-Piece Non-Metallic Raceway End Fittings