Search results

Panduct® PanelMax™ Corner Strip For DIN Rail Wiring Duct, 3" Corner Strip, PVC, Light Gray

Category: Wire Duct Clips / Retainers

TG raceway divider wall. Snaps onto rails in TG raceway base to create separate channels. Must use wire retainers to ensure channel separation per UL/CSA.

Category: Wall Duct Dividers

Single gang power rated two-piece snap together outlet box. Box accepts Pan-Way® Snap-On Faceplates. For use with Pan-Way® T-45 or LD, LDP, LDPH, LDS profile raceways. 5.00"L x 3.26"W x 1.62"H (127.1mm x 82.7mm x 41.1mm). Breakouts for 1/2", 3/4", or 1" d

Category: 1-Gang Raceway Device Boxes

Outside corner fitting. Used to join sections of TG raceway at outside corners. Fittings adjust from 85° to 135° to adapt to non-square corners.

Category: 1-Piece Non-Metallic Raceway Elbows

End Cap Fitting / TG-70 Series Raceway, Off-White

Category: 2-Piece Non-Metallic Raceway End Fittings

Fiber spool bracket, PVC, Gray, Each piece consists of two halves that snap into base of TG raceway. Provides method to contain one meter or more of fiber slack and acts as a strain relief while maintaining a minimum 32mm bend radius. Bracket separation can be adjusted to fit the length of slack required

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Right Angle Fitting / TG-70 Raceway, Non-Metallic, Off-White

Category: 2-Piece Non-Metallic Raceway Elbows

2 x 2 Vertical Tee, FiberRunner System, Yellow

Category: Wireway Cutoff Fittings

Transition fitting. Used to transition to T-70 raceway, Off White.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Backfeed Fitting, PVC, White, Allows Cable Entry Through The Back Of The T-70 Raceway

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

End cap fitting. Conduit breakouts of 1/2" for entry into raceway channel. Off White.

Category: 1-Piece Non-Metallic Raceway End Fittings

Reducer fitting for LD raceway from size 10 to size 5. For use with LD5 and LD10 raceway. Off White

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

TG raceway divider wall. Snaps onto rails in TG raceway rase to create separate channels. Must use wire retainers to ensure channel separation per UL/CSA.

Category: Wall Duct Dividers

End Cap, 2 x 2 Inch, Non-Metallic, Used on Opend Ends of Channel

Category: Wireway Closure Plates

Fiber spool bracket, PVC, Gray

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Panduct® PanelMax™ Corner Strip For DIN Rail Wiring Duct, 4" Corner Strip, PVC, Light Gray

Category: Wire Duct Clips / Retainers

Double gang power rated two-piece snap together outlet box. Box accepts Pan-Way® Snap-On Faceplates. For use with Pan-Way® T-45 or LD profile raceway. 5.00"L x 6.14"W x 1.62"H (127.1mm x 155.9mm x 41.1mm). Breakouts for 1/2", 3/4", or 1" diameter conduit.

Category: 2-Gang Raceway Device Boxes

Tee divider insert for TG-70 Raceway

Category: 1-Piece Non-Metallic Raceway Tee Fittings

GFCI 3-sided hanging box. Accepts single gang U.S. GFCI (ground fault circuit interrupter) standard electrical devices. Provides increased internal area for connections and excess wire.

Category: 1-Gang Raceway Device Boxes

3-sided hanging box. Mounts standard electrical outlets or communication devices with either NEMA standard single gang screw-on or Panduit snap-on faceplates. When used with TGDW divider wall, box separates and fully encloses device to provide cabling separation.

Category: 1-Gang Raceway Device Boxes

Base coupler fitting. Each piece includes two base coupler halves for joining sections of TG-70 base together, 10 pc.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 90° upward angle from a straight horizontal run. Used with outside vertical 90° angle fitting FOVRA2X2BL or FOVRA4X4BL to change level of straight horizontal runs. Cover included. Orange.

Category: 1-Piece Non-Metallic Raceway End Fittings

Reducer fitting for LD raceway from size 10 to size 3. For use with LD3 and LD10 raceway. For in-line terminations, use with CF10

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Adapter fits into universal breakout of DCEFX or RAEFX fittings. For use LD5, LDPH5, and LDS5 raceway, Off White, PVC, Length 0.81 in.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters