Conduit, Duct, & Raceway

Cable Runway Wall Angle Support fastens ladder rack to a wall or other flat surface. This Wall Angle Support, LWASK12G item fits 12.00 with a material of Steel color Gray.

Category: Cable Tray Mounting Hardware

Din Rails, Din3 Style (qty 4), Bulletin A54y (inline Instrumentation Enclosure Accessories), Size/dims: Fits 200mm, Material/finish: Steel/zinc

Category: Symmetrical Slotted DIN Rail

90-Degree Tee, Top/Front Cover, Material: Steel, Dimensions: 2" x 2"

Category: Wireway Tee Fittings

6" Divider, Telescopic Straight Section, Material: Stainless Steel

Category: Large 2-Piece Metallic Raceway Clips, Connectors, & Couplings

U-Connector, Used to Connect Two Straight Sections of Cable Tray, Dimensions: 2" x 2"

Category: Wireway U-Connectors

Lay-in Galvanized Wall Hangers are used to support a wireway run. This Support Hanger, F22GSHGV item measures 2.50x2.50 inches with a material of Steel finish Galvanized.

Category: Wireway Support Hangers

1/2 Inch Rigid 304 Stainless Steel 90 Degree Elbow

Category: Rigid 90° Conduit Elbows

Colored Snap-in Icon (Voice), package of 100, Black

Category: 1-Gang Raceway Device Boxes

1/2" Diameter, Reduced Wall Aluminum Conduit, Metallic, Lightweight Aluminum Alloy, 25 feet Reel.

Category: Flexible Aluminum Conduit

Wire Trough, Screw Cover, Bulletin F25 (Fiberglass Type 12 & 3R Wireway And Trough), Size/Dims: 4" x 4" x 24", Material/Finish: Fiberglass.

Category: NEMA 12 Wire Trough

Right angle fitting for use with LDPH5 and LDS5 raceway, Electric Ivory, ABS, Length 2.58 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Wireway 90° Elbow, NEMA Type 1, Lay-In, Outside Opening, Steel, Galvanized, Size: 6" x 6"

Category: Wireway Elbows

Adjustable Butt-Splice Kit (cULus Classified), Provides a Change In Up-and-Down Direction of the Cable Runway, It Can Be Adjusted to Any Angle from 0 to 90 Degrees, Made of Steel with a Painted or Plated Finish, Each Kit Connects One Ladder Rack Section to Another, Includes Mounting Hardware

Category: Cable Tray Splicer Kits

Wiring Trough, NEMA Type 1, Material: Steel, Dimensions: 4" x 4" x 60"

Category: NEMA 1 Wire Trough

Rack-to-Runway Mounting Plate Kit secures ladder rack to the top of equipment racks. This Rack-to-Runway Mounting Plate Kit, LRRMPGZ18 item Fits 12.00/18.00 with a material of Steel finish Plated.

Category: Cable Tray Mounting Hardware

CleanTray Telescopic Straight Section used for adjusting wireway length in frequent washdown areas. This Telescopic Straight Section CleanTray, CT66TSS item measures 6.00x6.00 inches with a material of SS304 finish Brushed.

Category: Cable Tray Dividers

Enclosure Adapter, 4.00x4.00, SS Type 304

Category: Wireway Panel Adapters

Ladder Rack Curved Sections (cULus Classified), Material: Steel, Width: 12"

Category: 90° Vertical Inside Cable Tray Bend

Splitter Trough, NEMA Type 1, Hinged Cover, Material: Steel, 4-Wire, Main Lugs Amps CU: 400, Main Lugs Wire Size Range: 1/0-250MCM: 4-600MCM, Dimensions: 48" x 10" x 6"

Category: NEMA 1 Wire Trough

Ww, Type 1, Telescope Ftg, Bulletin F40gf (galvanized Type 1 Lay-in Wireway Fittings), Size/dims: 6.00x6.00, Material/finish: Galvanized

Category: Wireway Telescope Fittings

Cut-Off Fitting, 6.00x6.00, Fiberglass

Category: Wireway Cutoff Fittings

Wireway, Elbow 45 Deg, Bulletin F25 (fiberglass Type 12 & 3r Wireway And Trough), Size/dims: 4.00x4.00, Material/finish: Fiberglass

Category: Wireway Elbows

Two-compartment Pole. Nominal Material Thickness .040" (1.0mm). Gray Boot Base.furnished Unwired Without Outlets. Mounting Hardware, Entrance End Plate And Ceiling Trim Plates Furnished. Length: 12' 5" (3.8m)

Category: Steel Power Poles

W-mold 2818fo-wh Ext Elbow Fo c5 White

Category: 1-Piece Non-Metallic Raceway Elbows