Search results

Panduct® type FS solid wall wiring duct, 1 W x 4 H, 6' length, PVC, light gray, no mounting holes.

Category: 2-Piece Non-Metallic Raceway

T-45 electrical bracket and box for installation of 106 duplex outlet, White.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2OR or FIVRA4X4OR to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

Inside corner fitting. Used to join cove raceway at inside corners. Maintains a minimum 1" bend radius of cabling.

Category: 1-Piece Non-Metallic Raceway Elbows

TG-70 raceway base, 8 foot length. Supplied with pre-punched mounting holes.

Category: 2-Piece Non-Metallic Raceway

Reducer fitting for LD raceway from size 10 to size 5. For use with LD5 and LD10 raceway. For in-line terminations, use with CF10

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Office Furniture Raceway End CapEnd cap fitting. Used to terminate office furniture raceway. Supplied with adhesive tape. Office Beige.

Category: 1-Piece Non-Metallic Raceway End Fittings

Raceway two-piece base and cover, TG-70, Off White, 8'

Category: 2-Piece Non-Metallic Raceway

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 8' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Reducing Fitting, 4x4 Fiber Duct, Cover Included, ABS, Yellow

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Tee fitting. Used to join sections of Twin-70 raceway at tee intersections, Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Tee Fittings

End cap fitting. Used to terminate or allow entry to T-70 raceway with conduit breakouts of 1/2" . International Gray.

Category: 1-Piece Non-Metallic Raceway End Fittings

Twin-70 raceway base, 10 foot length. Supplied with pre-punched mounting holes. 2' of cover needed for every 1' of Twin-70 base.

Category: 2-Piece Non-Metallic Raceway

Outside corner fitting. Used to join sections of Twin-70 raceway at outside corners. Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

2 x 2 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2BL or FIVRA4X4BL to change level of straight horizontal runs. Cover included.

Category: 1-Piece Non-Metallic Raceway Elbows

SLD DUCT NMTG PVC 3IN X5IN X6FT WHT 6FT

Category: 2-Piece Non-Metallic Raceway

Installation tool for use with type LD5 raceway.

Category: 2-Piece Non-Metallic Raceway

Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8', and 10' lengths, International Gray, Length 6.00 ft, Width 1.02 in.

Category: 2-Piece Non-Metallic Raceway

Panduct® type FS solid wall wiring duct, 3 W x 1 H, 6' length, PVC, white, no mounting holes.

Category: 2-Piece Non-Metallic Raceway

RACEWAY COVER IW 2M PK12

Category: 2-Piece Non-Metallic Raceway Covers

LDS5 Solid, 1-piece Power Rated RacewayTamper resistant one-piece surface raceway. Supplied with pre-applied adhesive backed tape, International Gray, PVC, Length 10.00 ft, Width 1.01 in.

Category: 2-Piece Non-Metallic Raceway

Tamper resistant one-piece surface raceway. Supplied with pre-applied adhesive backed tape, Off White, PVC, Length 10.00 ft, Width 1.01 in.

Category: 2-Piece Non-Metallic Raceway

Backfeed fitting. Allows cable entry through the back of the T-70 raceway. Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

OFR20 Single Channel, Low Voltage VerticOffice furniture vertical raceway. One-piece single channel raceway used to connect OFR20

Category: 1-Piece Non-Metallic Raceway Clips & Couplings