Search results

Raceway, Solid Wall, PVC, 4.25" x 3.12" x 6', Light Gray

Category: 2-Piece Non-Metallic Raceway

Conduit entrance end fitting. This power rated two-piece fitting is designed to accommodate the entrance of 1/2" conduit or align with knockouts on surface mount electrical boxes. For use with LD3/LDPH3 and has breakouts available to work with LD5/LDPH5 a

Category: 2-Piece Non-Metallic Raceway End Fittings

For right angle turns on the same surface. 1" [25mm] bend radius.

Category: 1-Piece Non-Metallic Raceway Elbows

For branches of raceway running at right angles. 1" [25mm] bend radius.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Outside corner fitting. Used to join sections of T-70 raceway at outside corners. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Elbows

Panduct® type FS solid wall wiring duct, 2 W x 2 H, 6' length, PVC, black.

Category: 2-Piece Non-Metallic Raceway

One-piece latching surface raceway with pre-applied adhesive backed tape, 6 foot length, International Gray, PVC, Length 6.00 ft.

Category: 1-Piece Non-Metallic Raceway

Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8', and 10' lengths, White, Length 8.00 ft.

Category: 2-Piece Non-Metallic Raceway

Office Furniture Corner Raceway End CapCorner raceway end cap fitting. Opening allows cord passage through fitting such as monitor and keyboard cables. Supplied with adhesive tape, Medium Tone.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Raceway Two Cubicle Drop FittingTwo cubicle drop fitting. Allows the transition from office furniture raceway run horizontally along partition wall to office furniture corner raceway mounted vertically in two cubicles at the intersection of partitions. Fitting maintains 1in minimum bend

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway 4 Way Cross FitCross fitting. Used to join sections of office furniture raceway at four corners. Supplied with adhesive tape, Office Gray.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 6' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Raceway Mid-Panel Tee FittingMid-panel tee fitting. Used to connect communication pole to office furniture raceway run horizontally along partition wall. Supplied with adhesive tape.Note: not intended for use at intersection of furniture panels. Office Gray.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Inside Center FInside corner fitting. Used to join sections of office furniture raceway at inside corner. Supplied with adhesive tape. Medium Tone.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway End Cap FittingEnd cap fitting. Used to terminate office furniture raceway. Supplied with adhesive tape. Medium Tone.

Category: 1-Piece Non-Metallic Raceway End Fittings

Office Furniture Raceway Double Spill-Over FittingDouble spill-over fitting. Fitting is used to spill over both sides of the furniture partitions at the same location. Incorporates a built-in, yet removable end cap that eliminates the need for additional raceway and fittings to terminate the pathway. Off

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Corner Raceway BaseOffice furniture corner raceway base. Used to terminate low voltage data cabling in the corner at the intersection of modular office furniture panels. Accepts 70mm standard faceplates. Available in 6' lengths.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway One Cubicle DropOne cubicle drop fitting. Allows the transition from office furniture raceway run horizontally along partition wall to office furniture corner raceway mounted vertically in one cubicle at the intersection of partitions. Fitting maintains 1in minimum bend

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 8' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Office Furniture Raceway Four Cubicle DropFour cubicle drop fitting. Allows the transition from office furniture raceway run horizontally along partition wall to office furniture corner raceway mounted vertically in four cubicles at the intersection of partitions. Fitting maintains 1" minimum ben

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Fire box adapter for use with LD10/LDPH10 profile raceway.NOTE: For low voltage applications only, Off White, ABS, Length 2.00 in.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

Office Furniture Corner Raceway BaseOffice furniture corner raceway base. Used to terminate low voltage data cabling in the corner at the intersection of modular office furniture panels. Accepts 70mm standard faceplates. Available in 6' lengths.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Double Spill-Over FittingDouble spill-over fitting. Fitting is used to spill over both sides of the furniture partitions at the same location. Incorporates a built-in, yet removable end cap that eliminates the need for additional raceway and fittings to terminate the pathway. Off

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway Right Angle FitRight angle fitting. Used to join sections of office furniture raceway at 90° flat junction. Supplied with adhesive tape, Medium Tone.

Category: 1-Piece Non-Metallic Raceway Elbows