2-Piece Raceway & Accessories

Inside Corner Fitting / TG-70 Raceway, Non-Metallic, Off-White

Category: 2-Piece Non-Metallic Raceway Elbows

Coupler Fitting / TG70 Series Raceway, Off-White, Minimum Bend Radius for High Performance Copper and Fiber Optic Cabling Systems per TIA/EIA 568-B and 569-B Requirements

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Entrance End Fitting / TG-70 Raceway, Non-Metallic, Electric Ivory

Category: 2-Piece Non-Metallic Raceway End Fittings

Wire retainer. Holds wires in place during installation.

Category: 2-Piece Non-Metallic Raceway Covers

End Cap Fitting / TG-70 Series Raceway, Off-White

Category: 2-Piece Non-Metallic Raceway End Fittings

Fiber spool bracket, PVC, Gray, Each piece consists of two halves that snap into base of TG raceway. Provides method to contain one meter or more of fiber slack and acts as a strain relief while maintaining a minimum 32mm bend radius. Bracket separation can be adjusted to fit the length of slack required

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Right Angle Fitting / TG-70 Raceway, Non-Metallic, Off-White

Category: 2-Piece Non-Metallic Raceway Elbows

Transition fitting. Used to transition to T-70 raceway, Off White.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Backfeed Fitting, PVC, White, Allows Cable Entry Through The Back Of The T-70 Raceway

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Fiber spool bracket, PVC, Gray

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

PAN FS3X4WH6NM SLD DUCT NMTG PVC 3"X4"X6' WHT 6FT

Category: 2-Piece Non-Metallic Raceway

Twin-70 raceway base, 8 foot length. Supplied with pre-punched mounting holes. 2' of cover needed for every 1' of Twin-70 base.

Category: 2-Piece Non-Metallic Raceway

Raceway Base and Cover, Above Floor, White, 6 Foot, 4-Channel

Category: 2-Piece Non-Metallic Raceway

Right angle fitting. Used to join sections of Twin-70 raceway at 90° flat junctions, Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Elbows

Optional split cover for the horizontal 45° angle fitting FRH4512X4BL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19 mm) opening for easy access to add or removes cables.

Category: 2-Piece Non-Metallic Raceway Covers

Conduit entrance end fitting. This power rated two-piece fitting is designed to accommodate the entrance of 1/2" conduit or align with knockouts on surface mount electrical boxes. For use with LD3/LDPH3 and has breakouts available to work with LD5/LDPH5 a

Category: 2-Piece Non-Metallic Raceway End Fittings

Optional split cover for the horizontal right angle fitting FRRA4X4OR. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19 mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

LD3 Low Voltage Drop Ceiling / EntranceLow voltage drop ceiling/entrance end fitting for use with LD3 raceway, Electric Ivory, ABS, Length 3.42 in, Width 1.6 in.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Panduct® type FS solid wall wiring duct, 2 W x 1 H, 6' length, PVC, light gray, no mounting holes.

Category: 2-Piece Non-Metallic Raceway

Panduct® type FS solid wall wiring duct, 2 W x 1 H, 6' length, PVC, white, no mounting holes.

Category: 2-Piece Non-Metallic Raceway

Optional split cover for the horizontal 45° angle fitting FRH456X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

Offset box and bracket for use with Pan-Way® Snap-on communication faceplates. Off White.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Pre-assembled 6in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Black, 1 piece.

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8', and 10' lengths, International Gray, Length 6.00 ft, Width 0.77 in.

Category: 2-Piece Non-Metallic Raceway