Search results

Panduct® type G wide slot wiring duct, 4 W x 2 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Offset box and bracket for use with NEMA Standard 70mm Screw-On Faceplates or Pan-Way® Electrical Snap-On Faceplates. Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Tee fitting for use with LDPH10 raceway only, Electric Ivory, ABS, Length 3.18 in.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Snap-on vertical sloped communication faceplate. Accepts four Panduit® Mini-Com® Modules (not included). No additional mounting hardware required, Electric Ivory.

Category: 1-Gang Raceway Box Covers & Faceplates

Used to protect cabling from threaded rod. Vertical slit allows easy installation. Black.

Category: Threaded Rod Protection Covers

End Cap Fitting For Use With LDPH5 And LDS5 Raceway, White, ABS, Length 1 in.

Category: 1-Piece Non-Metallic Raceway End Fittings

Inside corner fitting. Used to join sections of T-70 raceway at inside corners. Electric Ivory.

Category: 2-Piece Non-Metallic Raceway Elbows

Used to support the 6x4 and 4x4 systems attaching to the top of cabinets. Adjustable from 4 1/4" (108mm) to 9" (229mm) allowing runs to be leveled over uneven cabinet heights. Bracket is secured to the cabinet frame with through bolts (not included). The

Category: Mounting Hardware & Brackets

Used to support the 12x4 system from below with new threaded rod. Bracket is secured to threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16in nut driver on slide clamps. Also can be secured directly to the

Category: Mounting Hardware & Brackets

Used to support the 6x4 and 4x4 systems by spanning two threaded rod drops. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamp enables fast assembly to channel. Use 7/16in nut driver

Category: Mounting Hardware & Brackets

Used to support 12x4, 6x4, and 4x4 systems attaching to the top of the 19" wide version of the Panduit NF4PR84 4 post rack. Contains all hardware required to assemble bracket to the top of the 4 post rack. Bracket accepts 5/8" threaded rod (not included).

Category: Mounting Hardware & Brackets

Panduct® type F narrow slot wiring duct, 3 W x 3 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Panduct® type G wide slot wiring duct, 4 W x 4 H, 6' length, PVC, adhesive, light gray, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type H hinged cover wide slot wiring duct, 2 W x 2 H, 6' length, PVC, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8', and 10' lengths, White, PVC, Length 10.00 ft, Width 1.52 in.

Category: 2-Piece Non-Metallic Raceway

Panduct Wide Slot Wiring Duct, Type G, 1.75" W x 3.12" H x 6' L, Lead Free PVC, White, Adhesive Backing, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type G wide slot wiring duct, .5 W x .5 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Wiring Duct, Type G, Wide Slot, 1" W x 2" H x 6' L, PVC, White, Adhesive Backing, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Right angle fitting for use with LDPH3 and LDS3 raceway, White, ABS.

Category: 2-Piece Non-Metallic Raceway Elbows

Tamper resistant two-piece latching surface raceway. Supplied with pre-punched mounting holes and factory applied adhesive tape. Available in 6', 8', and 10' lengths, Electric Ivory, PVC, Length 6.00 ft, Width 1.52 in.

Category: 1-Piece Non-Metallic Raceway

Inside corner fitting for use with LDPH5 and LDS5 raceway, White, ABS, Length 2.11 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to support the 6x4 and 4x4 systems from any new threaded rod installations. Bracket is secured to threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps, For 1/2" Threaded Rod.

Category: Mounting Hardware & Brackets

The Wyr-Grid® Cantilever Bracket is black powder coated and is used to support the 12" (304.8 mm) Wyr-Grid® Pathway along a wall. It is 6.9" (175.3 mm) high, 14.7" (373.4 mm) long, 2.2" (56.4 mm) wide, and 14.7" (373.4 mm) deep and has an integral retaini

Category: Wire Duct Clips / Retainers

Raceway Base, T-70 Series, 4.07" x 1.77" x 8', Off White, Tamper Resistant

Category: 2-Piece Non-Metallic Raceway