Fiber Raceway Systems

Used to support the 12x4 system, dual 6x4, or dual 4x4 systems attaching to the top of cabinets. Adjustable from 4 1/4" (108mm) to 12" (305mm) allowing runs to be leveled over uneven cabinet heights. Bracket is secured to the cabinet frame with through bo

Category: Mounting Hardware & Brackets

Used to support the 24x4 system from new threaded rod installations. Bracket is secured to threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps.

Category: Mounting Hardware & Brackets

Provides secure, accessible route for cables spilling out from vertical tee to rack mounted equipment. Kit includes 6ft length of 4x4 capacity hinged duct, 6ft length of 4x4 hinged duct cover, one end cap for 4x4 hinged duct, three FZBA1.5X4 adjustable Z

Category: Drop-Offs, Spillouts & Outlets

Used to support the 6x4 and 4x4 systems by spanning two threaded rod drops. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamp enables fast assembly to channel. Use 7/16in nut driver

Category: Mounting Hardware & Brackets

Assembled into the 12x4 vertical tee FRVT12X4YL. Allows for the transition to 4x4 Fiber-Duct™ Channel with minimal space required. No tools required for assembly. Black color only.

Category: End Caps & Reducers

Optional split cover for the horizontal tee with 4x4 exit fitting FRT12X4W6BL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19 mm) opening for easy access to add or remove cables.

Category: Tees, Crosses & Junctions

Used to support the 24x4 system by spanning two 1/2" existing threaded rod drops. Can be installed from above or below. Bracket is secured to each threaded rod with two split nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16"

Category: Mounting Hardware & Brackets

Used to support the 12x4 system by attaching to underfloor pedestals. (Contains all necessary hardware.) Use on pedestals up to 2" in diameter. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps.

Category: Mounting Hardware & Brackets

Used to fully enclose 12x4 channel in conjunction with the Spill-Over Junction FRSPJ2X2BL. Cover snaps onto the channel base. Hinged feature allows easy access to add or remove cables.

Category: Drop-Offs, Spillouts & Outlets

Used to support the 6x4 and 4x4 systems by attaching to underfloor pedestals. (Contains all necessary hardware.) Use on pedestals up to 1" in diameter. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps.

Category: Mounting Hardware & Brackets

Used to support the 12x4 system by spanning two threaded rod drops that are 18in apart. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16in

Category: Mounting Hardware & Brackets

Optional split hinged cover for the channel FR4X4YL2. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables. Snap-on hinge feature enables positioning of cover at angles between 30° and 90°.

Category: Covers & Retainers

Used to support the 12x4 system from new threaded rod installations. Bracket is secured to threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver on slide clamps.

Category: Mounting Hardware & Brackets

The fiber mounting FiberRunner® QuikLock™ Threaded Rod Trapeze Bracket for Wyr-Grid® 12" (305mm) width is used to support a FiberRunner® 4x4 and 6x4 Channel above or below the Wyr-Grid® 12" Pathway using the same 1/2" or 12mm threaded rod used to support

Category: Mounting Hardware & Brackets

Used to support the 12x4 system by spanning two threaded rod drops that are 18in apart. Can be installed from above or below. Bracket is secured to each threaded rod with two nuts. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16in

Category: Mounting Hardware & Brackets

Optional snap-on hinged cover for channel FR6X4BL6. Hinge feature enables positioning of cover at angles between 30° and 90°.

Category: Covers & Retainers

Strut mounting clip assembly allows FiberRunner® Channel or Wyr-Grid® Pathway to be attached directly to standard 1 5/8" wide strut structures. Contains two clips and all hardware for assembly. Bolts release with 7/16" nut driver.

Category: Mounting Hardware & Brackets

Pre-assembled 6in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Black, 20 pieces.

Category: Couplers & Joiners

Optional snap-on hinged cover for channel FR12X4BL6. Can be folded down for height restricted areas.

Category: Covers & Retainers

Optional snap-on cover for channel FR24X4YL10. Supplied in four 30 long pieces.

Category: Covers & Retainers

Used to support the 6x4 and 4x4 systems attaching directly to any 3/8 (9.5mm) x 1 1/2" (38.1mm) or 3/8" (9.5mm) x 2" (50.8mm) ladder rack rail. No threaded rod required. The pre-assembled slide clamps enable fast assembly to channel. Use 7/16" nut driver

Category: Mounting Hardware & Brackets

Fitting that transitions from ADC's 4x4 FiberGuide System to 4x4 FiberRunner® System. Fitting has a black finish and is made from metal. Attachment hardware is included.

Category: Couplers & Joiners

The fitting attaches any 6" x 4" (150mm x 100mm) FiberRunner® fitting or channel to the 4" x 4" (100mm x 100mm) Fiber-Duct™ Channel S4X4YL6 or E4X4YL6. It is yellow and made of ABS plastic. It includes a solid cover.

Category: End Caps & Reducers

Optional snap-on hinged cover for channel FR4X4BL6. Hinge feature enables positioning of cover at angles between 30° to 90°.

Category: Covers & Retainers