Search results

FIBER-DUCT™ FIBERRUNNER® Cover, for 4" Wide PANDUCT Wiring Duct, Lead-free PVC, Yellow, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Wire Duct Covers

T70/Twin70 Raceway Divider Wall, 10' Length, PVC, Gray, Snaps onto rails in T-70/Twin-70 raceway base to create separate channels. Must use wire retainers to ensure channel separation per UL/CSA.

Category: Wall Duct Dividers

Right Angle Fitting,LD3/LDPH3/LDS3 Raceway, Non-Metallic, Rigid PVC, Off-White, One Inch Bend Radius for TIA/EIA Compliance

Category: 1-Piece Non-Metallic Raceway Elbows

Snap-on single gang 106 duplex electrical/communication faceplate. Used to cover one NEMA standard 106 duplex electrical outlet. In communication applications, covers one standard 106 duplex communication module frame.

Category: 1-Gang Raceway Box Covers & Faceplates

Right angle fitting for use with LD5, LDPH5, and LDS5 raceway, Off White, ABS, Length 2.58 in.

Category: 1-Piece Non-Metallic Raceway Elbows

Solid hinged duct, 1.5 W x 2 H, 6' length, PVC, light gray, no mounting holes, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® Type H Wide Slot Wiring Duct with Hinged Cover, 3-1/4 Inch Wide x 4 Deep x 6 Foot Length, PVC, Black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type NE halogen-free wiring duct, .5 W x .5 H, 6' length, halogen-free, white, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type FS solid wall wiring duct, 3 W x 3 H, 6' length, PVC, light gray, no mounting holes.

Category: 2-Piece Non-Metallic Raceway

Outside Corner Fitting, Series LD10, Non-Metallic, Off-White

Category: 1-Piece Non-Metallic Raceway Elbows

Panduct® Type NE Halogen-Free Slotted Wiring Duct , 1 Inch x 3 Inch x 6 Foot, White, Polyphenylene Oxide, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Special Purpose Wire Duct

Tee Fitting, For Use With LD10 and LDPH10 Raceway, Off-White

Category: 1-Piece Non-Metallic Raceway Tee Fittings

T-45 raceway base with pre-punched mounting holes, 10 foot length.

Category: 1-Piece Non-Metallic Raceway

Coupler for LD10 Raceway, Off-White, ABS, 2" Long

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Offset Box For Snap-On Faceplates, T-70, PVC, Off-White

Category: 1-Gang Raceway Device Brackets & Plates

Panduct® Type HN Narrow Slot Wiring Duct with Hinged Cover, 1.75 W x 1.98 D x 72 Inch H, PVC, Light Gray, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

End cap fitting for use with LD3 raceway, Off White, ABS, Length 1.2 in.

Category: 1-Piece Non-Metallic Raceway End Fittings

Right Angle Fitting For Use With LD10 and LDPH10 Raceway, Off-White

Category: 1-Piece Non-Metallic Raceway Elbows

Entrance end fitting. Conduit breakouts of 1/2", 3/4", 1" and 1 1/4" which allows entry from ceiling or wall.

Category: Small 2-Piece Metallic Raceway End Fittings

The FiberRunner® 6x4 Channel can be used with fittings and brackets to design a routing system to segregate, route, and protect fiber optic and high-performance copper cables. The cable routing channel accepts cable retainers or a hinged cover.

Category: Straight Sections

Panduct® Type H Wide Slot Wiring Duct with Hinged Cover, 4 Inch Wide x 4 Deep x 6 Foot Length, PVC, Black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

T-45 inside corner fitting, Off White.

Category: 2-Piece Non-Metallic Raceway Elbows

Transition Fitting Cover, Used To Transition To Any LD Profile Or T-45 Raceway

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Non-Metallic Surface Raceway, One-Piece, Hinged, Electric Ivory, Type LD10, 1.51 Inch Wide x .94 Inch High x 8 Foot Long

Category: 1-Piece Non-Metallic Raceway