Search results

Panduct® type F narrow slot wiring duct, 4 W x 3 H, 6' length, PVC, black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Used to fully enclose the 6x4 dual downspout fitting FRDDS6X4BL. Cover is attached to the fitting base with three hinge clips. The hinge clips allow the hinged cover to rotate to a fully closed position and an open position greater than 90°.

Category: Straight Cable Tray Covers

Pre-assembled 4in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Orange, 1 piece.

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Inside corner fitting. Used to join sections of TG raceway at inside corners. Fittings adjust from 85° to 135° to adapt to non-square corners. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Elbows

Pre-assembled 4in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Yellow, 20 pieces.

Category: 2-Piece Non-Metallic Raceway Clips & Couplings

Attaches to 12x4 channel and/or fittings to create at a horizontal four way cross intersection with two 6x4 exits. Accepts optional split cover FRFWCSC12W6BL.

Category: 2-Piece Non-Metallic Raceway Connectors & Adapters

Attaches to 12x4 channel and/or fitting to create a 45° downward angle from a straight horizontal run. Used with inside vertical 45° angle fitting FRIV4512X4YL to change level of a horizontal run. Accepts optional split cover FROV45SC12YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Optional split cover for the four way cross fitting FRFWC12X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 2-Piece Non-Metallic Raceway Covers

Attaches to 4x4 channel and/or fittings to create a 90° vertical drop from a horizontal run. Hinged door included. Accepts FTR4X4OR, FIDT4X4BL, S4X4OR6 or E4X4OR6 directly. Accepts optional snap-on cover FRHC4OR6 in conjunction with channel.

Category: 1-Piece Non-Metallic Raceway Elbows

Type NC halogen-free wiring duct cover, 100mm W x 2M length, halogen-free, light gray.

Category: Wire Duct Covers

Used to fully enclose 12x4 channel in conjunction with the spill-over junction FRSPJ4X4YL. Cover snaps onto the channel base. Hinged feature allows easy access to add or remove cables.

Category: Straight Cable Tray Covers

LD2P10 Power Rated 1-piece Multi-ChannelTwo channel tamper resistant one-piece latching surface raceway. Supplied with pre-applied adhesive backed tape. Available in 8' and 10' lengths.

Category: 1-Piece Non-Metallic Raceway

Used to fully enclose 4x4 channel in conjunction with the Spill-Over Junction FRSPJ2X2OR. Cover snaps onto the channel base. Hinged feature allows easy access to add or remove cables.

Category: Straight Cable Tray Covers

Used for closing off open ends of the hinged channel or fittings. No coupler required. Push-on installation, Black.

Category: Wireway Closure Plates

Panduct® type FS solid wall wiring duct, 3 W x 5 H, 6' length, PVC, light gray, no mounting holes.

Category: 2-Piece Non-Metallic Raceway

Outside corner fitting. Used to join sections of Twin-70 raceway at outside corners. White.

Category: 1-Piece Non-Metallic Raceway Elbows

Single gang one-piece deep outlet box with adhesive backing. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® LD profile raceway. 5.23in L x 3.48in W x 2.75in H (133.0mm x 88.5mm x 69.8mm). Breakou

Category: 1-Gang Raceway Device Boxes

Panduct® type G wide slot wiring duct, 3 W x 2 H, 6' length, PVC, intrinsic blue, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type H hinged cover wide slot wiring duct, 1.5 W x 3 H, 6' length, PVC, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Snap-on 2-position flush mount faceplate accepts any Panduit® NetKey® Module and most other manufacturers' keystone modules. Compatible with Panduit® Fast-Snap™ Outlet Boxes, Surface Raceway Systems, and Pan-Pole™ Outlet Poles, Off White.

Category: 1-Gang Raceway Box Covers & Faceplates

Panduct® type G wide slot wiring duct, 4 W x 4 H, 6' length, PVC, adhesive, black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type G wide slot wiring duct, .5 W x 1 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Single gang two-piece screw together extension outlet box. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® LD profile raceway. 4.99in L x 3.30in W x 1.00in H (126.7mm x 83.8mm x 25.4mm). Breakouts

Category: 1-Gang Raceway Device Boxes

Single gang two-piece snap together outlet box with adhesive backing. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® T45 or LD profile raceway. 5.00"L x 3.26"W x 1.62"H (127.1mm x 82.7mm x 41.1m

Category: 1-Gang Raceway Device Boxes