Search results

Optional split cover for the horizontal tee fitting FRT4X4BL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19 mm) opening for easy access to add or remove cables.

Category: Tees, Crosses & Junctions

Inside corner fitting. Used to join sections of TG raceway at inside corners. Fittings adjust from 85° to 135° to adapt to non-square corners. Electric Ivory.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to fully enclose the 6x4 dual downspout fitting FRDDS6X4BL. Cover is attached to the fitting base with three hinge clips. The hinge clips allow the hinged cover to rotate to a fully closed position and an open position greater than 90°.

Category: Drop-Offs, Spillouts & Outlets

Single Channel NEMA Device Plate Fitting, Gray

Category: Large 2-Piece Metallic Raceway Cover Plates

WMDDS4017DG

Category: Large 2-Piece Metallic Raceway Elbows

Single gang two-piece screw together extension outlet box. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® LD profile raceway. 4.99in L x 3.30in W x 1.00in H (126.7mm x 83.8mm x 25.4mm). Breakouts

Category: 1-Gang Raceway Device Boxes

Panduct® type G wide slot wiring duct, 4 W x 4 H, 6' length, PVC, adhesive, black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Panduct® type G wide slot wiring duct, .5 W x 1 H, 6' length, PVC, adhesive, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

Single gang two-piece snap together outlet box with adhesive backing. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® T45 or LD profile raceway. 5.00"L x 3.26"W x 1.62"H (127.1mm x 82.7mm x 41.1m

Category: 1-Gang Raceway Device Boxes

Single gang two-piece screw together intermediate outlet box. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® LD profile raceway. 5.12in L x 3.38in W x 2.27in H (130.2mm x 86.0mm x 57.7mm). Breako

Category: 1-Gang Raceway Device Boxes

Splice Washer, 4.00x4.00x8.00, Lt Gray, Steel

Category: Cable Tray Nut, Bolt, & Clamp Assemblies

Channel, Slotted Wall, 2" x 2" (50mm x 50mm), 6', Fiber-Duct, Orange, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Standard Density Wire Duct

W-mold G20ig306 Gry 3w1ckt Pl ugmold

Category: Single Circuit Steel Plugmold

For connecting vertical runs of DS4000 Series Raceway with OFR Series Raceway. Includes removable divider than can be positioned to feed any raceway channel.

Category: Metallic Overfloor Raceway Connectors & Adapters

4 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Yellow.

Category: End Caps & Reducers

Duct cover with protective film, 4 W x 6' length, PVC, intrinsic blue, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Wire Duct Covers

The Wyr-Grid® Pathway Section protects cables between the Main Distribution Area and the Equipment Distribution Area. Unlike other pathways, it installs quickly and can be modified easily, optional sidewalls snap on without extra hardware or tools. Splice

Category: Straight Wire Basket

Double gang two-piece screw together outlet box. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use withPan-Way® LD profile raceway. 5.05"L x 5.05"W x 1.62"H (131.9mm x 87.7mm x 44.4mm). Breakouts for 1/2", 3/4", or 1" diameter conduit.

Category: 1-Gang Raceway Device Boxes

Attaches to 4x4 channel and/or fittings to create a 45° downward angle from a horizontal run. Used with inside vertical 45° angle fitting FRIV454X4YL to change level of a straight horizontal run. Accepts optional split cover FROV45SC4YL.

Category: Elbows & Bends

1" bend radius corner strip pre-cut for 2" wall height.

Category: Wireway Elbows

Fast-Snap™ Double Gang Power Rated Two-Piece Snap Together Outlet Box. Box accepts Pan-Way® Snap-On Faceplates. For use with Pan-Way® T-45 or LD profile raceway. 5.00"L x 6.14"W x 1.62"H (127.1mm x 155.9mm x 41.1mm). Breakouts for 1/2", 3/4", or 1" diamet

Category: 2-Gang Raceway Device Boxes

Attaches any 4x4 FiberRunner® Fitting or Channel to the 2x2 Fiber-Duct™ Channel, S2X2BL6 or E2X2BL6 or 2x2 FiberRunner® Channel, HS2X2BL6 or H2X2BL6. Note: Attachment to 2x2 FiberRunner® Channel requires a QuikLock™ Coupler FBC2X2BL. Includes solid cover.

Category: End Caps & Reducers

Cut-to-size 6 foot corner strip with a 1" bend radius.

Category: Wireway Elbows

6 foot length is cut by user to fit duct height, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Special Purpose Wire Duct