Search results

24 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Black.

Category: 1-Piece Non-Metallic Raceway End Fittings

Power rated drop ceiling/entrance end fitting for use with LD3, LDPH3, LDS3, LD5, LDPH5, LDS5, LD10 and LDPH10 raceway. Use CA3 or CA5 adapters for LD3/LDPH3/LDS3 and LD5/LDPH5/LDS5 profile raceway, adapters not required for LD10 and LDPH10 raceway, Inter

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches to 4x4 channel and/or fitting to create a 45° upward angle from a straight horizontal run. Used with outside vertical 45° angle fitting FROV454X4OR to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

12 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Black.

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches to 12x4 channel and/or fittings to create a 90° horizontal branch with a 12x4 exit from straight horizontal run. Accepts optional split cover FRTSC12BL.

Category: 1-Piece Non-Metallic Raceway Elbows

Base coupler fitting. Used for joining sections of Twin-70 base together. White.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches any 6x4 FiberRunner® Fitting or Channel to any 4x4 FiberRunner® Fitting or Channel. Accepts split cover FRRF6FR4SCBL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel base and/or fittings to create a 90° vertical turn down from a straight horizontal run. Accepts optional split cover FROVRASC4OR.

Category: 1-Piece Non-Metallic Raceway Elbows

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from the 12x4 channel or a 12x4 horizontal tee, Black.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Raceway Spill Over FittingSpill-over fitting. Allows transition from office furniture raceway run horizontally along partition wall to office furniture vertical raceway in one location. Adjustable fitting maintains 1in minimum bend radius of cabling and works with various panel wi

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Used to limit the bend of the fiber cable to 2 (50.4 mm) when exiting from 4x4 FiberRunner® Channel or a FiberRunner® Horizontal Tee, Orange.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

Attaches to 6x4 channel base and/or fittings to create a 90° vertical drop from horizontal runs. Hinged door included. Accepts FIDT4X4BL, FTR4X4BL, S4X4BL6, E4X4BL6 directly. Accepts optional snap-on cover FRHC6BL6 in conjunction with channel.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 12x4 channel and/or fittings to create a 90° horizontal branch with a 12x4 exit from straight horizontal run. Accepts optional split cover FRTSC12YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Entrance end fitting. Conduit breakouts of 1/2", 3/4", 1", and 1 1/4" which allows entry from ceiling or wall. International Gray.

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches to 12x4 channel and/or fitting to create a 45° horizontal turn from a straight horizontal run. Accepts optional split cover FRH45SC12BL.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 12x4 channel and/or fittings to create a 90° horizontal branch with a 4x4 exit from straight horizontal run. Accepts optional split cover FRTSC12W4BL.

Category: 1-Piece Non-Metallic Raceway Elbows

The FiberRunner® 4-Way Cross Channel Fitting is used in cable management to create a horizontal 4-way cross intersection with two 6 inch x 4 inch exits. It also attaches to 6x4 channels and/or fittings. The 4-way cross channel fitting accepts the optional split cover.

Category: 1-Piece Non-Metallic Raceway Connectors & Adapters

TG-70 Base Coupler FittingBase coupler fitting. Each piece includes two base coupler halves for joining sections of TG-70 base together.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

OFR20 Single Channel, Low Voltage 1-piecOne-piece single channel low voltage raceway with adhesive tape backing for data cable routing along top of modular furniture partitions. Available in 8' lengths.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 4x4 channel and/or fitting to create a 45° upward angle from a straight horizontal run. Used with outside vertical 45° angle fitting FROV454X4BL to change level of a straight horizontal run. Includes split cover.

Category: 1-Piece Non-Metallic Raceway Elbows

Attaches to 6x4 channel and/or fittings to create a 90° vertical turn from a straight horizontal run. Accepts optional split cover FROVRASC6YL.

Category: 1-Piece Non-Metallic Raceway Elbows

Optional split cover for the horizontal tee fitting FRT12X4BL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: 1-Piece Non-Metallic Raceway Tee Fittings

OFR20 Single Channel, Low Voltage VerticOffice furniture vertical raceway. One-piece single channel raceway used to connect OFR20

Category: 1-Piece Non-Metallic Raceway Clips & Couplings

Office Furniture Raceway, Non-Metallic, .88" x 1.71" x 6', Office Gray

Category: 1-Piece Non-Metallic Raceway