Search results

Power rated drop ceiling/entrance end fitting for use with LD3, LDPH3, LDS3, LD5, LDPH5, LDS5, LD10 and LDPH10 raceway. Use CA3 or CA5 adapters for LD3/LDPH3/LDS3 and LD5/LDPH5/LDS5 profile raceway, adapters not required for LD10 and LDPH10 raceway, Inter

Category: 1-Piece Non-Metallic Raceway End Fittings

Attaches any 6x4 FiberRunner® Fitting or Channel to any 4x4 FiberRunner® Fitting or Channel. Accepts split cover FRRF6FR4SCYL.

Category: End Caps & Reducers

Attaches to 24x4 channel and/or fittings to create a 45° upward angle from a straight horizontal run. Used with outside vertical 45° angle fitting FROV4524X4YL to change level of a straight horizontal run. Includes cover.

Category: Elbows & Bends

Panduct® flush cover type D round hole wiring duct, 1.5 W x 4 H, 6' length, PVC, white, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: Special Purpose Wire Duct

12 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Yellow.

Category: End Caps & Reducers

FIBERRUNNER CHANNEL 12X4 OR 6FT

Category: Straight Sections

Attaches to 24x4 channel and/or fittings to create a 45° horizontal turn from a straight horizontal run, Yellow.

Category: Elbows & Bends

4 x 4 Fiber-Duct Fitting. Attaches to channel to create a 45° downward angle from a straight horizontal run. Used with inside vertical 90° angle fitting FIVRA2X2OR or FIVRA4X4OR to change level of straight horizontal runs. Cover included.

Category: Wireway Elbows

The fitting attaches any 12x4 FiberRunner® Fitting or Channel to any 6x4 FiberRunner® Fitting or Channel while transitioning to the left. It is black and made of ABS plastic. It accepts split cover FRRF126LSCBL.

Category: End Caps & Reducers

24 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Black.

Category: End Caps & Reducers

Attaches to 12x4 channel and/or fittings to create a horizontal four way cross intersection with two 6x4 exits. Accepts optional split cover FRFWCSC12W6YL.

Category: Tees, Crosses & Junctions

The L-bracket with quick mount clip is used for installing the CWD3 corner wiring duct. It is made of low-carbon steel and spring steel and comes in a package of 16 pieces. The recommended fastener size is #10 – 32 x 1/2" (not included).

Category: Small 2-Piece Metallic Raceway Clips, Connectors, & Couplings

FIBERRUNNER COVER 12X4 OR 6FT

Category: Covers & Retainers

Optional split cover for the four way cross fitting FRFWC6X4OR. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: Tees, Crosses & Junctions

Pre-Assembled Coupler for 6" x 4" Fiber Runner Channel, ASB Plastic, Yellow

Category: Couplers & Joiners

Outside corner fitting for use with LDPH5 and LDS5 raceway, Electric Ivory, ABS, Length 1.25 in.

Category: 1-Piece Non-Metallic Raceway Elbows

2in x 2in coupler fitting used to join two sections of duct together. Fiber-Duct™ Coupler is not required at each fitting connection, Orange

Category: Wireway U-Connectors

Single gang two-piece screw together deep outlet box. Box accepts Pan-Way® Screw-On Faceplates or any NEMA standard single gang faceplate. For use with Pan-Way® T-45, LD2P10 (when used with JBD1), or LD profile raceway. 5.19in L x 3.45in W x 2.75in H (131

Category: 1-Gang Raceway Device Boxes

The FiberRunner® 4-Way Cross Channel Fitting is used in cable management to create a horizontal 4-way cross intersection with two 6 inch x 4 inch exits. It also attaches to 6x4 channels and/or fittings. The 4-way cross channel fitting accepts the optional split cover.

Category: Tees, Crosses & Junctions

FIBERDUCT FITTINGENDCAP 2INX2IN OR EA

Category: Wireway Closure Plates

Assembled into the 6x4 vertical teeFRVT6X4YL or 4x4 vertical tee FRVT4X4YL with an audible snap, Allows for the transition to 2x2 FiberRunner® or 2x2 Fiber-Duct™ Channel with minimal space required. No tools required for assembly. Black color only.

Category: End Caps & Reducers

Panduct® type F narrow slot wiring duct, 1 W x 1 H, 6' length, PVC, black, SOLD IN 6 FOOT INCREMENTS, ORDER OF 6 FT = 1 PIECE OF DUCT

Category: High Density Wire Duct

Attaches to 4x4 channel and/or fitting to create a 45° upward angle from a straight horizontal run. Used with outside vertical 45° angle fitting FROV454X4OR to change level of a straight horizontal run. Includes split cover.

Category: Elbows & Bends

Attaches to 24x4 channel and/or fittings to create a horizontal four way cross intersection with two 24x4 exits. Accepts optional split cover FRFWCCV24YL.

Category: Tees, Crosses & Junctions