Fittings

Optional split cover for the outside vertical 45° angle fitting FROV4512X4YL. Snap-on feature allows cover to be installed and removed with no tools required. Creates radiused 3/4 (19mm) opening for easy access to add or remove cables.

Category: Elbows & Bends

Spill-Over Junction with 4x4 Exit. Assembles onto 4x4, 6x4, 12x4, or 24x4 FiberRunner® Channel, spilling over the side into a 4x4 vertical exit. Requires coupler to attach 4x4 FiberRunner® Channel and fittings to the vertical exit. Mounts directly to exis

Category: Drop-Offs, Spillouts & Outlets

Attaches any 4x4 FiberRunner® Fitting or Channel to the 2x2 Fiber-Duct™ Channel, S2X2YL6 or E2X2YL6 or 2x2 FiberRunner® Channel, HS2X2YL6 or H2X2YL6. Note: Attachment to 2x2 FiberRunner® Channel requires a QuikLock™ Coupler FBC2X2YL. Includes solid cover.

Category: End Caps & Reducers

Attaches to 12x4 channel and/or fittings to create a 90° horizontal branch with a 6x4 exit from straight horizontal run. Accepts optional split cover FRTSC12W6BL.

Category: Tees, Crosses & Junctions

The fitting attaches any 12x4 FiberRunner® Fitting or Channel to any 6x4 FiberRunner® Fitting or Channel. It is black and made of ABS plastic. It accepts split cover FRRF126SCBL.

Category: End Caps & Reducers

Attaches to 12x4 channel and/or fittings to create a horiztonal four way cross intersection with two 12x4 exits. Accepts optional split cover FRWCSC12BL.

Category: Tees, Crosses & Junctions

Pre-assembled 6in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Black, 1 piece.

Category: Couplers & Joiners

Used to route cable into one or two pieces of 1.5 (38mm) diameter split corrugated tubing. Requires coupler to be used with 4x4 FiberRunner® Fitting. Used with any 4x4 FiberRunner® Fitting, Black.

Category: Drop-Offs, Spillouts & Outlets

Attaches to 4x4 channel and/or fittings to create a 90° horizontal branch from straight horizontal runs. Accepts optional split cover FRTSC4OR.

Category: Tees, Crosses & Junctions

Used to fully enclose 6x4 channel in conjunction with the Spill-Over Junction FRSPJ2X2OR. Cover snaps onto the channel base. Hinged feature allows easy access to add or remove cables.

Category: Drop-Offs, Spillouts & Outlets

Attaches to 6x4 channel base and/or fittings to create a 90° vertical drop from horizontal runs. Hinged door included. Accepts FIDT4X4BL, FTR4X4OR, S4X4OR6, E4X4OR6 directly. Accepts optional snap-on cover FRHC6OR6 in conjunction with channel.

Category: Tees, Crosses & Junctions

Used to limit the bend radius of the cable to 2 (50.8mm) when exiting from 6x4 channel, 6x4 horizontal tee fitting, or 6x4 exit on 12x4 vertical tee, Black.

Category: Drop-Offs, Spillouts & Outlets

Fitting and Cover, Horizontal 90o Angle, 2" x 2" (50mm x 50mm), Fiber-Duct, LG

Category: Elbows & Bends

Attaches to 12x4 channel and/or fittings to create a 90° vertical drop from a horizontal run. Hinged door included. Requires coupler to attach FRTR6X4YL or FRIDT6X4YL to vertical exit. Accepts optional snap-on cover FRHC12YL6 in conjunction with channel.

Category: Tees, Crosses & Junctions

Pre-assembled 12in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Yellow, 1 piece.

Category: Couplers & Joiners

6x4 Horizontal Tee Fitting, 90° Horizontal Branch, H: 4.22", W: 10.77", Accepts optional split cover FRTSC6YL

Category: Tees, Crosses & Junctions

The FiberRunner® End Cap Fitting is used in cable management to close off open ends of the channel or fittings. The FiberRunner® End Cap Fitting is a push-on installation and does not require a coupler.

Category: End Caps & Reducers

The FiberRunner® 4x4 Spill-Over Fitting Cover is used to fully enclose 4x4 channel in conjunction with the 4x4 spill-over junction. The spill-over junction cover snaps onto the channel base. It has a hinged feature that allows easy access to add or remove cables.

Category: Drop-Offs, Spillouts & Outlets

The FiberRunner® 2x2 Spill-Over Junction Fitting is used in cable routing systems. It assembles onto 4x4, 6x4, 12x4, or 24x4 FiberRunner® Channels. It mounts directly to the existing installation with no alteration required. The spill-over junction fitting includes mounting hardware.

Category: Drop-Offs, Spillouts & Outlets

Pre-assembled 24in x 4in QuikLock™ coupler quickly joins two sections of channel and/or fittings. Mechanically attaches without tightening bolts. Bolts release using 3/8in nut driver to allow coupler to be removed if necessary, Yellow, 1 piece.

Category: Couplers & Joiners

4 x 4 Fiber-Duct Fitting. Attaches to channel to create a 90° horizontal turn from a straight horizontal run. Cover included. Orange.

Category: Elbows & Bends

6 x 4 end cap fitting used for closing off open ends of the channel or fittings. No coupler required. Push-on installation, Orange.

Category: End Caps & Reducers

The fitting attaches any 12x4 FiberRunner® Fitting or Channel to any 6x4 FiberRunner® Fitting or Channel while transitioning to the right. It is black and made of ABS plastic. It accepts split cover FRRF126RSCBL.

Category: End Caps & Reducers

Attaches to 4x4 channel and/or fittings to create a 45° downward angle from a horizontal run. Used with inside vertical 45° angle fitting FRIV454X4BL to change level of a straight horizontal run. Accepts optional split cover FROV45SC4BL.

Category: Elbows & Bends